Why pay for this single file when you have it + over 500 more for a lot less? That’s right. STLFLIX is a multi-theme ever-growing library of STL files. Your One-Stop-Shop for Premium 3D-Printing models. Get started with the Ultimate STL platform!

Click here to join STLFLIX

It’s a Mushroom Lamp

This STL file is recommended for FDM Printers!
3D Printing Time:
Approximately Height :  21 cm

The perfect lamp for fans of mushrooms and videogames. This not bio but very luminescent fungi needs little assembly and it’s completely support free. It’s also not that big, so you won’t need mush-room to store it. Get it? Nevermind, it’ll grow on you.

Electrical Installation Instructions

What you’ll need:

All “It’s a Mushroom Lamp” printed parts

LED Module

Electrical Plug (2.1mm DC Jack 12V)

On-off Switch (15mm x 10mm 12V)

Power Supply (12V 1A)

Solder

Soldering Iron

20cm wire (3x)

Electrical Tape

Instructions:

Take two 20cm wires (if you used our recommendations, that’d be one black and one red) and strip 10mm on each end.
Use solder to attach one end of the black wire to one of the pins of the 12v Power Jack and one end of the red wire to the other pin.

Thread the wires through the round hole on the It’s a Mushroom Lamp_Stand in a way that the plug faces the outside of the lamp.
Thread only the red wire through the rectangle hole on the It’s a Mushroom Lamp_Stand from the inside to the outside, then solder it to the On-Off Switch on the pin aligned to the "0" (off).

Take another 20cm length black wire and solder one of its ends to the remaining pin of the On-Off Switch.

Thread the other end of the new black wire through the rectangle hole on the It’s a Mushroom Lamp_Stand  from the outside to the inside, pulling it to the top.

Gently knot one of the black wires so you can identify which is linked to the On-Off Switch and which is linked to the Power Jack.

Place the It’s a Mushroom Lamp_Led_Cover on top of the mushroom body and thread both black wires through one of the lateral holes.

Cut a stripe of 4 led modules from the rest, and separate them by cutting the double sided tape that links them together. Do not cut the wires between them.

Remove the double sided tape protection from the last module of the stripe and attach it to the It’s a Mushroom Lamp_Led_Cover.
In order, go around the It’s a Mushroom Lamp_Led_Cover gluing the modules. Once you reach the last one, make the wire connection between gluing it to the Led Cover.

Take the wire you identified from the On-Off Switch and connect it to the positive wire from the led module. Use the wire coming from the Power Jack to connect the negative wire from the led module.

Wrap the links in electrical tape to avoid short circuits. After all that, glue the module to the It’s a Mushroom Lamp_Led_Cover.

Place the already assembled mushroom hat on the circle on top of the It’s a Mushroom Lamp_Led_Cover.

Plug your power supply onto the outlet and connect it to the power jack. You can now turn your mushroom light on!

Line Width/ Nozzle: 0.4 mm
First Layer Line Width: 0.48 mm / 120%
Average Speed: 20mm/s (First Layer) / 30mm/s (All the other layers) / 20 mm/s (First Layer) / 500 mm/s (All the other layers on Bambu Lab)
Recommended Initial Layer Height:  0.16 mm
Recommended Layer Height:  0.16 mm
Recommended Perimeters/ Walls: 3.
Recommended Infill (%): 10% (Gyroid)
Needs Support: No.
Build Plate Adhesion: Skirt.
 

The parameters above are recommendations made by our staff; if you prefer, you can adapt them according to your preferences.

COPYRIGHT & SELLING RIGHTS

This STL file is copyrighted by STLFLIX©, the Ultimate STL Subscription. This means you can print it for yourself, but you DO NOT have the right to sell it.

To acquire copyright & selling rights, you must subscribe to our Commercial License. By doing so, you will also get immediate access to over 500 STL files, unlimited downloads, and marketing content for every single file.

Go commercial and skyrocket your own store with STLFLIX!

GO COMMERCIAL!

USEFUL LINKS

Get to know us a little better!

Website | Instagram | TikTok | Twitter

What are you waiting for? Join thousands of other makers from all around the world.

HAPPY PRINTING!